Understanding Motor Controls
4th Edition
ISBN: 9781337798686
Author: Stephen L. Herman
Publisher: Delmar Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 31, Problem 13RQ
Refer to the schematic diagram in Figure 31–8. Assume that the motor is not running. When the third speed push button is pressed, the motor starts in its lowest speed. After a delay of 3 seconds, the motor accelerates to second speed and 3 seconds later to third speed. After a period of about 1 minute, the fourth speed push button is pressed, but the motor does not accelerate to fourth speed. Which of the following could cause this problem?
- a. Control relay CR2 coil is open.
- b. S2 contactor coil is open.
- c. CR3 coil is shorted.
- d. S3 contactor coil is open.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The piston rod of a double-acting cylinder is to advance when a 3/2- way push button valve is actuated manually. The cylinder is to remain advanced until a second valve is actuated. The signal of the second valve can only take effect after the first valve has been released. The cylinder is to then return to the initial position. The cylinder is to remain in the initial position until a new start signal is given. The speed of the cylinder is to be adjustable in both directions.Draw the circuit diagram for the problem.
What is the mechanism's Degree of Freedom
The reversing motor,which is controlled by two power relays,can be rotated in both directions as shown in the figure beiow.When the motor is mechanically combined with a lead screw,the rotary motion is converted to a linear one,such as the one moving lef tor right on the worktable in the layout.The desired direction of rotation is selected via the two STAFIT buttons,respectively.The limit switches LS1 and LS2,located at the two extreme motion limits,ensure 1-rqtf we forget to stop the movement of the worktable,then it will stop automatically, and the mechanism of the layout will not be destroyed.Draw the circuit of automation.
Chapter 31 Solutions
Understanding Motor Controls
Ch. 31 - Prob. 1RQCh. 31 - Prob. 2RQCh. 31 - A wound rotor induction motor has a stator that...Ch. 31 - Name three factors that determine the amount of...Ch. 31 - Prob. 5RQCh. 31 - Explain why controlling the rotor current also...Ch. 31 - What is the function of a micro limit switch when...Ch. 31 - Prob. 8RQCh. 31 - What is rotor slip?
Ch. 31 - Prob. 10RQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Refer to the circuit shown in Figure 25–5. Assume that timer TR1 is set for a delay of 10 seconds and timer TR2 is set for a delay of 5 seconds. When the START button is pressed, the motor starts. After 10 seconds the S1 contacts open and the motor continues to accelerate, but never reaches full speed. After a delay of about 30 seconds, the motor trips out on overload. Which of the following could cause this problem? TR1 coil is open. S2 coil is open. S1 coil is open. R coil is open.arrow_forwardThe device that prevents the engine from turning the armature of the starter motor is the. overrunning clutch pinion gear flywheel pole shoearrow_forwardRefer to the circuit shown in Figure 241. Assume that timer TR is set for a delay of 10 seconds. When the START button is pressed, the motor starts in low speed. After a delay of 30 seconds the motor is still in its lowest speed and has not accelerated to normal speed. Which of the following could not cause this condition? a. The START button is shorted. b. Timer coil TR is open. c. Contactor coil R is open. d. Timed contact TR did not close after a delay of 10 seconds.arrow_forward
- Refer to the circuit shown in Figure 16-11. Assume that the platform is located on the lower floor. When the UP push button is pressed, the platform rises. When the platform reaches the upper floor, however, the pump does not turn off but continues to run until the overload relay opens the overload contacts. Which of the following could cause this problem? a. The solenoid valve opened when limit switch LS1 opened. b. The UP push button is shorted. c. Limit switch LS1 did not open its contacts. d. Limit switch LS2 contacts did not reclose when the platform began to rise.arrow_forwardRefer to the circuit shown in Figure 4221. Assume that the THIRD SPEED push button is pressed. The motor starts in second speed, skipping first speed. After 5 seconds, the motor accelerates to third speed. Which of the following could cause this problem? a. S1 contactor coil is open. b. CR1 contactor coil is open. c. TRl timer coil is open. d. S1 load contacts are shorted.arrow_forwardRefer to the circuit shown in Figure 33–7. When the low speed push button is pressed, the motor begins to run in low speed. When the high speed push button is pressed, the motor stops running. Which of the following could cause this problem? The 1L contactor coil is open. H contactor coil is open. PR relay coil is open. The 2L contactor coil is open.arrow_forward
- Refer to the circuit shown in Figure 16-11. Assume that the platform is located on the bottom floor. When the UP push button is pressed the pump motor does not start. Which of the following could not cause this problem? The contacts of limit switch LS1 are open. The contacts of limit switch LS2 are open. Motor starter coil M is open. The overload contact is open.arrow_forwardFor the circuit shown, give the sequence of operation of cylinders 1 and 2 when the pump is turned on. Assume both cylinders are initially fully retracted. CYLINDER 1 CYLINDER 2 Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle repeats. Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle stops. Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle repeats. O Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle stops..arrow_forwardUse time delay A push button is to control the forward stroke after the piston rod has reached the forward end position the components are to be pressed together for 20 seconds then the piston rod is to return automatically to the initial position Additional condition The return stroke must occur even if the start push button is still depressed A new start signl may only become effective after the initial position has been reached and after the push button has been releasedarrow_forward
- Refer to the circuit shown in Figure 15-6. The STOP button is shown to be an emergency STOP button. What does the symbol used for the STOP button actually represent?arrow_forwardIn relation to the circuit presented below, mark the alternative(s) that you consider correct. 1 To enable actuator A2 to advance, it is necessary to switch valve V2 to the leftmost position and ensure that valve V1 is in its initial (intermediate) position. 2 Switching valve V2 to the leftmost position allows actuator A2 to advance, but for this to happen, valve V1 must also be switched to the leftmost position. 3 When activating valve V1, using the locking lever installed on the left side of it, the two actuators (A1 and A2) are allowed to advance. 4 Hydraulic pump B1 is a simple variable displacement type. 5 Valves V1 and V2 have a TANDEM center.arrow_forwardFor the circuit shown, give the sequence of operation of cylinders 1 and 2 when the pump is turned on. Assume both cylinders are initially fully retracted. CYLINDER 1 CYLINDER 2 U O Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle stops.. O Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle stops. O Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle repeats. O Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle repeats.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License