Statics and Mechanics of Materials
2nd Edition
ISBN: 9780073398167
Author: Ferdinand P. Beer, E. Russell Johnston Jr., John T. DeWolf, David Mazurek
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 4.3, Problem 54P
To determine
(a)
The magnitude of the vertical force P required for maintaining equilibrium.
To determine
(b)
The reactions at A and B.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A small winch is used to raise a 120-lb load. Find (a) the magnitude of the vertical force P that should be applied at C to maintain equilibrium in the position shown, (b) the reactions at A and B , assuming that the bearing at B does not exert any axial thrust.
The spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless surface rests against the shaft at B. If a 60-lb force P is exerted on the spanner at D, find the reactions at A and B.
A lever AB is hinged at C and attached to a control cable at A . If the lever is subjected to a 75-lb vertical force at B , draw the freebody diagram needed to determine the tension in the cable and the reaction at C.
Chapter 4 Solutions
Statics and Mechanics of Materials
Ch. 4.1 - For the beam and loading shown, determine (a) the...Ch. 4.1 - A 3200-lb forklift truck is used to lift a 1700-lb...Ch. 4.1 - A gardener uses a wheelbarrow to transport a 250-N...Ch. 4.1 - A load of lumber of weight W=25 kN is being raised...Ch. 4.1 - Three loads are applied as shown to a light beam...Ch. 4.1 - Three loads are applied as shown to a light beam...Ch. 4.1 - For the beam and loading shown, determine the...Ch. 4.1 - Prob. 8PCh. 4.1 - Prob. 9PCh. 4.1 - The lever BCD is hinged at C and attached to a...
Ch. 4.1 - The lever BCD is hinged at C and attached to a...Ch. 4.1 - A lever AB is hinged at C and attached to a...Ch. 4.1 - Determine the reactions at A and B when...Ch. 4.1 - Prob. 14PCh. 4.1 - Prob. 15PCh. 4.1 - Prob. 16PCh. 4.1 - A light bar AD is suspended from a cable BE and...Ch. 4.1 - Prob. 18PCh. 4.1 - Prob. 19PCh. 4.1 - Two slots have been cut in plate DEF, and the...Ch. 4.1 - A 6-m telephone pole weighing 1600 N is used to...Ch. 4.1 - Prob. 22PCh. 4.1 - For the and crate of Prob. 4.22 and assuming that...Ch. 4.1 - A tension of 20 N is maintained in a tape as it...Ch. 4.1 - The bracket ABC can be supported in the eight...Ch. 4.1 - Eight identical 500750-mm rectangular plates, each...Ch. 4.2 - Determine the reactions at B and C when a=30mm.Ch. 4.2 - Prob. 28PCh. 4.2 - A 12-ft wooden beam weighing 80 lb is supported by...Ch. 4.2 - Prob. 30PCh. 4.2 - One end of rod AB rests in the comer A and the...Ch. 4.2 - Using the method of Sec. 4.2B, solve Prob. 4.12.Ch. 4.2 - Prob. 33PCh. 4.2 - A 40-lb roller of 8-in. diameter, which is to be...Ch. 4.2 - Member ABC is supported by a pin and bracket at B...Ch. 4.2 - Prob. 36PCh. 4.2 - Prob. 37PCh. 4.2 - For the frame and loading shown, detennine the...Ch. 4.2 - For the boom and loading shown, determine (a) the...Ch. 4.2 - A slender rod BC of length L and weight W is held...Ch. 4.2 - Prob. 41PCh. 4.2 - Prob. 42PCh. 4.2 - Prob. 43PCh. 4.2 - Prob. 44PCh. 4.2 - Solve Prob. 4.44, assuming that the 170-N force...Ch. 4.2 - Prob. 46PCh. 4.2 - Prob. 47PCh. 4.2 - Prob. 48PCh. 4.2 - Prob. 49PCh. 4.2 - Prob. 50PCh. 4.3 - Two transmission belts pass over a double-sheaved...Ch. 4.3 - Solve Prob. 4.51, assuming that the pulley rotates...Ch. 4.3 - A 48-ft sheet of plywood weighing 40 lb has been...Ch. 4.3 - Prob. 54PCh. 4.3 - Prob. 55PCh. 4.3 - Prob. 56PCh. 4.3 - Prob. 57PCh. 4.3 - Prob. 58PCh. 4.3 - Prob. 59PCh. 4.3 - Prob. 60PCh. 4.3 - A 48-in. boom is held by a ball-and-socket joint...Ch. 4.3 - Prob. 62PCh. 4.3 - The 6-m pole ABC is acted upon by a 455-N force as...Ch. 4.3 - A 600-lb crate hangs from a cable that passes over...Ch. 4.3 - The horizontal platform ABCD weighs 60 lb and...Ch. 4.3 - Prob. 66PCh. 4.3 - Prob. 67PCh. 4.3 - Prob. 68PCh. 4.3 - A 10-kg storm window measuring 9001500 mm is held...Ch. 4.3 - Prob. 70PCh. 4.3 - Prob. 71PCh. 4.3 - Solve Prob. 4.69, assuming that the hinge at A has...Ch. 4.3 - Prob. 73PCh. 4.3 - Three rods are welded together to form a corner...Ch. 4.4 - Determine whether the block shown is in...Ch. 4.4 - Prob. 76PCh. 4.4 - Determine whether the block shown is in...Ch. 4.4 - Prob. 78PCh. 4.4 - Prob. 79PCh. 4.4 - Prob. 80PCh. 4.4 - Prob. 81PCh. 4.4 - Prob. 82PCh. 4.4 - Prob. 83PCh. 4.4 - Knowing that P=100N, determine the range of values...Ch. 4.4 - A 120-lb cabinet is mounted on casters that can be...Ch. 4.4 - Prob. 86PCh. 4.4 - A 40-kg packing crate must be moved to the left...Ch. 4.4 - A 40-kg packing crate is pulled by a rope as...Ch. 4.4 - Prob. 89PCh. 4.4 - Prob. 90PCh. 4.4 - Prob. 91PCh. 4.4 - Prob. 92PCh. 4.4 - Prob. 93PCh. 4.4 - Prob. 94PCh. 4.4 - Prob. 95PCh. 4.4 - Prob. 96PCh. 4.4 - The cylinder shown is of weight W and radius r,...Ch. 4.4 - Prob. 98PCh. 4 - A T-shaped bracket supports the four loads shown....Ch. 4 - Neglecting friction and the radius of the pulley,...Ch. 4 - Member ABC is supported by a pin and bracket at B...Ch. 4 - Prob. 102RPCh. 4 - Prob. 103RPCh. 4 - Prob. 104RPCh. 4 - Prob. 105RPCh. 4 - Prob. 106RPCh. 4 - Prob. 107RPCh. 4 - Prob. 108RPCh. 4 - Prob. 109RPCh. 4 - Two 10-lb blocks A and B are connected by a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.arrow_forwardThe 80-lb homogeneous plate is supported by a ball-and-socket joint at A, a slider hearing at B, and the cable CE. A 120-lb vertical force is applied to the corner D. Determine the force in the cable and the magnitude of the bearing reaction at B.arrow_forwardThe uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to support the bar, find the magnitudes of the reactions at A and B.arrow_forward
- The connections at the ends of bars AB and BC arc ball-and-socket joints. Neglecting the weights of the bars, determine the force in cable DE and the reaction at A.arrow_forwardFind the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.arrow_forwardThe spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless surface rests against the shaft at B. Given that a 320-N force P is exerted on the spanner at D. Find the component of the reaction at A in a direction perpendicular to AC.arrow_forward
- A light rod AD is supported by frictionless pegs at B and C and rests against a frictionless wall at A. A vertical 120-lb force is applied at D. Determine the reactions at A, B, and C.arrow_forwardA foldable tray for the paper supply of a photocopy machine is shown. The tray is supported by a single hinge at A and two slotted links (one on each side of the tray). If the stack of paper weighs 14 N and other weights may be neglected, determine the reactions at point B for one of the links when D = 190 mm.arrow_forwardThere are two identical cylinder namely cylinders M and P with equal weight weighing 441.45 Newtons which are both supported by a smooth plane. Assume that all contact of the cylinder are smooth surface, determine all the reactions on cylinder M. Solve using equilibrium of concurrent force system.arrow_forward
- A 20-kg cover for a roof opening is hinged at corners A and B . The roof forms an angle of 30° with the horizontal, and the cover is maintained in a horizontal position by the brace CE . Draw the free-body diagram needed to determine the magnitude of the force exerted by the brace and the reactions at the hinges. Assume that the hinge at A does not exert any axial thrust.arrow_forwardRod AD is acted upon by a vertical force P at end A and by two equal and opposite horizontal forces of magnitude Q at points B and C . Derive an expression for the magnitude Q of the horizontal forces required for equilibrium.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Engineering Basics - Statics & Forces in Equilibrium; Author: Solid Solutions - Professional Design Solutions;https://www.youtube.com/watch?v=dQBvQ2hJZFg;License: Standard YouTube License, CC-BY