Concept explainers
For the system shown in Fig. 8.17, compute the power delivered by the pump to the water to pump
Learn your wayIncludes step-by-step video
Chapter 8 Solutions
Applied Fluid Mechanics (7th Edition)
Additional Engineering Textbook Solutions
Statics and Mechanics of Materials (5th Edition)
Applied Statics and Strength of Materials (6th Edition)
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Engineering Mechanics: Dynamics (14th Edition)
- Water enters a pump through a 250 mm diameter pipe at 35 kPa. It leaves the pump at 140 kPa through 1 150 mm diameter pipe. If the flow rate is 150 L/s. Compute the energy head added by pump in meters. note: indicate the free body diagramarrow_forwardPatrick is building a cabin on a hillside and has proposed the water system shown below. The distribution tank in the cabin maintains a pressure of 27 psig above the water. There is an energy loss of 14.6 lb*ft/lb in the piping. When the pump is delivering 37 gal/min of water, compute the horsepower delivered by the pump to the water. PA = Submit Question Distribution tank 4 ft Flow hp 214 ft Pump 1 ftarrow_forwardA horizontal 150 mm diameter pipe gradually reduces its section to 50 mm diameter, subsequently enlarging into 150 mm section. The pressure in the 150-mm pipe at a point just before entering the reducing section is 140 kPa and in the 50 mm section at the end of the reducer, the pressure is 70 kPa. If 600 mm of head is lost between the points where the pressures are known, compute the rate of flow of water through the pipe.arrow_forward
- 3. The pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 75 L/min to a tank 3.5m above the pump. The pressure at A is -20 kPa and the pressure at B is 275 kPa. The head loss in the system is 2.5 times the velocity head in the discharge pipe. Calculate the power (kW) delivered by the pump for pipe diameter at suction in 52.54mm and discharge pipe diameter is 26.64mm.arrow_forwardReducer connection connecting a pipe that carries water with a diameter of A (mm) and another with a diameter of B (mm). If the pressure difference between the two ends of the joint is equal to C (mm) of mercury, calculate the average velocity at the inlet and outlet sections, and find the volumetric flow rate if the loss is small that can be neglected.arrow_forwardWater at 20°C is being pumped from tank 1 to tank 2 with given conditions. Calculate thepower of pump used in the system. (Both tanks are open to atmosphere)arrow_forward
- A pump draws water from reservoir A and lifts it to reservoir B. The loss of head from A to 1 is 3 times the velocity head in the 6 inch pipe and loss of head from 2 to B is 20 times the velocity head in the 4 inch pipe. Compute the horsepower output of the pump and the pressure heads at 1 and 2 when the discharge is 200 pgm. B EL 240 ft Water 4 inch pipe EL 0 Pump 2. Water EL -20 ft 6 inch pipearrow_forwardA pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. Find the power delivered by the pump in kW. Calculate the pressure head at point 1 in meters. Solve the pressure head at point 2 in meters.arrow_forwardCalculate the pressure of the air in the sealed tank shown in the figure that would cause the volume flow rate of 500 gal/min from the nozzle. The depth h is 10 ft.arrow_forward
- Water at 20 Celcius degrees is pumped from a large reservoir through a pipe system which has a diameter of 79 mm and length of 13 m. The installation of pipe system is as shown in the figure below. Considering the mass flow of the water supplied to the pipe is 5,1 kg/s and the surface roughness of the pipe is equal to the 5 micron, please compute the total pressure loss of the system in Pascal.arrow_forward6. A Compressor of a compressed air system displaces air at 25 cubic meters per minute when the intake pressure is 101.4 kPa. Compute the time required to pump up a 9 cubic meter receiver from 550 kPa to 828 kPa if the average volumetric efficiency of the compressor is 70%arrow_forwardSaturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of the piping is in 5-in. schedule 40 steel pipe. If the 2 fittings used is 90° ell standard long radius, The pump has an efficiency of 80%. Calculate the kW power needed for the pump. Calculate the total friction losses in kJ/kg.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY