Obtain a pan of water and form a barrier in it that has a wide slit as shown. Place a dowel in the water and gently rock it back and forth to generate straight wavefronts at a constant rate.
Gradually decrease the width of the slit until it is completely closed. Observe the wavefronts in Region II as you makethis change.
1. Describe how the shape of the wavefronts in Region II is affected as the width of the slit is decreased.
2. Compare the spacing of the wavefronts in the two regions (I and II). Is the spacing of the wavefronts in Region II affected by changing the width of the slit?
Explain how your observation of the spacing of the waefronts is consistent with the relative wave speeds in the two regions.
3. How, if at all, does the amplitude of the wave in Region II change when the slit is made slightly narrower? In particular, consider two cases in which:
•the slit is initially very wide and is made slightly narrower.
•the slit is initially very narrow and is made even narrower.
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
Tutorials in Introductory Physics
Additional Science Textbook Solutions
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Conceptual Integrated Science
College Physics
College Physics (10th Edition)
Physics: Principles with Applications
College Physics: A Strategic Approach (4th Edition)
- Please show work and circle answer A laser beam of wavelength 670 nm shines through a diffraction grating that has 750 lines/mm. Sketch the pattern that appears on a screen 1.0 m behind the grating, noting distances on your drawing and explaining where these numbers come from.arrow_forwardIf light with a wavelength of 480 nm is used in a two-slit experiment with a barrier with slits that are 0.05 mm apart that is 1.6 m from the projection screen. What is the distance from the center of the first and third dark fringes? Show your work.arrow_forwardA plane wave hits a piece of glass whose front surface is spherical and whose back surface is plane. The radius of the lens is 10 cm and the thickness of the glass is 1 cm at the center, as shown in the diagram at right. At time t1, the center of the plane wavefront has just reached the lens. A short time later, at time t2, the center of the wavefront will have passed completely through the glass, as shown. a) Find the time that elapses between t1 and t2, the time it takes the center of the wavefront to pass thorugh the middle 1 cm of the glass. b) Find the amount by which the edges of the wavefront at t2 will be ahead of the cetner of the wavefront, due to the fact that these edges passed through empty space, with no glass in their paths.arrow_forward
- Please answer it short and easy to understand.How does a single slit affect the wave pattern? How does a double slit affect the wave pattern?arrow_forwardYou just won a brand new laser pen and you want to know the wavelength of the light, so you set up Young’s double-slit experiment and observe the interference pattern on screen 1.2 meters away from the slits. The slits are 0.25 mm apart and you measure the distance between the centers of the first dark fringes on either side of the central maximum to be 3 mm. What is the wavelength of your new laser? If visible, what color should it appear, if not visible state the region of the EM spectrum? Hint: Draw a picture.arrow_forwardTwo loudspeakers are placed above and below each other, as shownand driven by the same source at a frequency of400Hz. An observer is in front of the speakers (to the right) at pointO, at the same distance from each speaker. What minimum vertical distance upward should the top speaker be moved to create constructive interference at pointO?The speed of sound is 343m/s. Pls show all your workarrow_forward
- While researching the use of laser pointers, you conduct a diffraction experiment with two thin parallel slits. Your result is the pattern of closely spaced bright and dark fringes shown in (Figure 1) (Only the central portion of the pattern is shown.) You measure that the bright spots are equally spaced at 1.53 mm center to center (except for the missing spots) on a screen that is 2.50 m from the slits. The light source was a helium–neon laser producing a wavelength of 632.8 nm. How far apart are the two slits? How wide is each slit?arrow_forwardShown below is the central part of the interference pattern for a pure wavelength of red light projected onto a double slit. The pattern is actually a combination of singleand double-slit interference. Note that the bright spots are evenly spaced. Is this a double- or single-slit characteristic? Note that some of the bright spots are dim on either side of the center. Is this a single- or double-slit characteristic? Which is smaller, the slit width or the separation between slits? Explain your responses.arrow_forwardTwo slits of width 3 μm, each in an opaque material, are separated by a center-to-center distance of 7.5 μm. A monochromatic light of wavelength 400 nm is incident on the double-slit. One finds a combined interference and diffraction pattern on the screen. How many peaks of the interference will be observed in the central maximum of the diffraction pattern? Please show all the work! Thanks!arrow_forward
- What minimum path length is needed to introduce a phase shift of 205° in light of wavelength 566 nm? (Give your answer in nm.) What phase shift will that path difference you calculated in part (a) introduce in light of wavelength 799 nm? (Give you answer in degree.)arrow_forwardPlease show formula and units For the figure shown below, let R = 1.20 m and d = 0.120 mm and assume the slit system is illuminated with monochromatic 500 nm light. The first bright fringe (m = 1) happens at point P. Calculate the phase difference (ϕ) between the two wave fronts arriving to point P in radians when: a) θ = 0.500⸰ b) y = 5.00 mm. The value of θ in part b is not the same as the value of θ from part a. However, you may assume that θ in part b is small.arrow_forwardFor the figure shown below, the two sources are 6cm apart, and they are in phase. Two paths are drawn from the sources to a point. (The picture is to scale, even if the sources are not 6cm apart on the paper.) (a) If the wavelength of the two sources is 2cm, for the picture, figure out whether the point marks a position of constructive or destructive interference. (b) Repeat if the wavelength is 1cm.arrow_forward
- University Physics Volume 3PhysicsISBN:9781938168185Author:William Moebs, Jeff SannyPublisher:OpenStaxPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-Hill