Manufacturing Processes for Engineering Materials (6th Edition)
6th Edition
ISBN: 9780134290553
Author: Serope Kalpakjian, Steven Schmid
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 2.66P
To determine
To Plot: The true stress vs true strain curve that material for specimen b should have for the bar to remain horizontal.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A tension test was performed on a specimen having an original diameter of 12.5 mm and a gage length of 50mm.
The data are listed in the table below:
Complete the following:
Plot the stress-strain curve. Label the y-axis every 50 MPa, and the x-axis every 0.05 mm/mm.
Plot the linear portion of the stress-strain curve (first 5 points). Label the y-axis every 50 MPa, and the x-axis every 0.001 mm/mm.
Determine the approximate Modulus of Elasticity
Determine the approximate Ultimate Stress
Determine the approximate Fracture Stress
Determine the approximate Modulus of Resilience
Determine the approximate Modulus of Toughness
Other Requirements:
Provide an example hand-written calculation showing how you calculated one point on the curve.
Remember to properly label your plots and provide axis labels with units.
Hand sketched plots will not be accepted. Use Excel or similar software.
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is
transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain =
0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in
the y-direction, the width strain was measured to be gw=-0.1000 at that instant.
The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi.
Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test
specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the
sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be
expected.
(Suppose you need to design a tension test machine capable of testing specimens that have nominal ultimate stresses as high as σu = 100 ksi . How much force must the machine be capable of generating? Assume the testing specimen has the ASTM shape shown. Answer for this is 19.6 kip)
(If the maximum nominal strain is ϵf = 0.7 just before the test specimen fractures and the test machine operates by moving only one grip, how far must that grip be designed to travel? The total length of the deforming part of the specimen is 3 in. Answer for this is 2.10 in)
Do not know if this info is needed but this was the other 2 parts
Chapter 2 Solutions
Manufacturing Processes for Engineering Materials (6th Edition)
Ch. 2 - Prob. 2.1QCh. 2 - Prob. 2.2QCh. 2 - Prob. 2.3QCh. 2 - Prob. 2.4QCh. 2 - Prob. 2.5QCh. 2 - Prob. 2.6QCh. 2 - Prob. 2.7QCh. 2 - Prob. 2.8QCh. 2 - Prob. 2.9QCh. 2 - Prob. 2.10Q
Ch. 2 - Prob. 2.11QCh. 2 - Prob. 2.12QCh. 2 - Prob. 2.13QCh. 2 - Prob. 2.14QCh. 2 - Prob. 2.15QCh. 2 - Prob. 2.16QCh. 2 - Prob. 2.17QCh. 2 - Prob. 2.18QCh. 2 - Prob. 2.19QCh. 2 - Prob. 2.20QCh. 2 - Prob. 2.21QCh. 2 - Prob. 2.22QCh. 2 - Prob. 2.23QCh. 2 - Prob. 2.24QCh. 2 - Prob. 2.25QCh. 2 - Prob. 2.26QCh. 2 - Prob. 2.27QCh. 2 - Prob. 2.28QCh. 2 - Prob. 2.29QCh. 2 - Prob. 2.30QCh. 2 - Prob. 2.31QCh. 2 - Prob. 2.32QCh. 2 - Prob. 2.33QCh. 2 - Prob. 2.34QCh. 2 - Prob. 2.35QCh. 2 - Prob. 2.36QCh. 2 - Prob. 2.37QCh. 2 - Prob. 2.38QCh. 2 - Prob. 2.39QCh. 2 - Prob. 2.40QCh. 2 - Prob. 2.41QCh. 2 - Prob. 2.42QCh. 2 - Prob. 2.43QCh. 2 - Prob. 2.44QCh. 2 - Prob. 2.45QCh. 2 - Prob. 2.46QCh. 2 - Prob. 2.47QCh. 2 - Prob. 2.48QCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - Prob. 2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. 2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. 2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. 2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. 2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. 2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. 2.76PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. 2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. 2.82PCh. 2 - Prob. 2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. 2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. 2.92PCh. 2 - Prob. 2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. 2.99PCh. 2 - Prob. 2.100PCh. 2 - Prob. 2.101P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a compressive load of 3 kN is applied parallel to the 2.3m dimension, what is the resulting engineering normal strain?arrow_forwardA rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.arrow_forwardIn a creep test, a material with E = 600 MPa is initially loaded with a stress o, = 297 MPa. 1.5 hr after the initial loading, the strain in the material is measured to be 0.12, and after another hour, it is found to be 0.1832. What will be the strain in the material 3 hours after the initial loading? How much time did it take for the strain to reach a value of 0.001?arrow_forward
- TEST YOUR UNDERSTANDING! The tension stress-strain diagram for a square bar (50 x 50 mm²; L = 600 mm) is shown in the figure. If the applied load is 500 kN, determine the elongation and the new side length of the specimen. The shear modulus is G = 83 GPa. 1. What is the modulus of elasticity of the material? 2. What is the Poisson's ratio of the material? 3. What is the lateral strain of the material? Answer to Test your understanding box 1. 200 GPa 2. 3. 4. (MPa) 0.2048 2.048 x 104 49.9898 mm 400 0.002 (TYU 2-2) What is the new side length of the material? 5. If a force applied to the material elongates the material by 3 mm, what happens to the material if the force is removed? Why? (mm/mm)arrow_forwardA tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?arrow_forwardBy application of tensile force, the cross-sectional area of bar Pis first reduced by 30% and then by an additional 20% Another bar Q of the same material is reduced in cross-sectional area by 50% in a single step by applying tensile force After deformation, the true strain in bar Pand bar Q will, respectively be (a) 0.5 and 05 (b) 0.58 and 0.69 (c) 0.69 and 0.69 (d) 0.78 and 1.00arrow_forward
- A strain rosette was attached to the outer surface of stainless vessel when the vessel is in a stress-free state. The vessel was then put under a complex loading (pressure, bending and torsion) state. The train readings for the three strain gage elements in the strain rosette were recorded as: Ea=210, Eb=160, Ec-330, all in micro-strains. The mechanical properties of the stainless material are known: E=193 GPa, G=76 GPa, v=0.27, oy=205 MPa. Calculate the following: 1. Principal strains and in-plane maximum shear strain. 2. Principal stresses and absolute maximum shear stress. 3. The factor-of-safety based on the maximum shear stress failure theory. 4. The factor-of-safety based on the maximum distortion energy failure theory. 45° 45° b 45° strain rosette Xarrow_forwardNormal forces (F1, F2, and F3) are uniformly applied across the faces of a rectangular polycrystalline block of material, as shown in the attached photo. The dimensions of the block are S1 = 5 cm, S2 = 12 cm, and S3 = 4 cm. Calculate the normal engineering strain in the X2 direction due to the resulting elastic deformation. Use the following if needed: E = 250 GPa, ν = 0.35, μ = 56 GPa, F1 = 50 kN, F2 = 10 kN, and F3 = 5 kN.arrow_forwardA circular solid piece of rock is tested in a compression testing rig to examine its stress/strain behavior. The sample is 6 inches in diameter and 12 inches in length, with the compression load cell imposing a constant load of 10000 lbf equally at both the top and bottom of the rock sample. Assuming a measured reduction in length of 0.02 inches, find the compressive stress and strain of the rock.arrow_forward
- The data shown in the accompanying table are From a tensile test of high-strength steel. The test specimen has a diameter of 0.505 in. and a gage length of 2.00 in. (see figure for Prob. 1.5-3). At fracture, the elongation between the gage marks is 0.12 in. and the minimum diameter is 0.42 in. Plot the conventional stress-strain curve for the steel and determine the proportional limit, modulus of elasticity (the slope of the initial part of thestress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 2.00 in., and percent reduction in area. TENSILE-TEST DATA FOR PROB. L.5-7 Laid (lb) Elongation (in) 1000 0.0002 2000 0.0006 6000 0.0019 10,000 0.0033 12,000 0.0039 12,900 0.0041 13,400 0.0047 13,600 0.0054 13,800 0.0063 14,000 0.0090 14,400 0.0102 15,200 0.0130 16,800 0.0230 18,400 0.0336 20,000 0.0507 22,400 0.1108 22,600 Fracturearrow_forwardThe data below are for a thin steel wire suitable for use as a guitar string. Ultimate tensile stress: 1.8 x 109 Pa Young Modulus: 2.2 x 1011 Pa Cross-sectional area: 2.0 x 10-7 m2 In a tensile test, a specimen of the wire, of original length 1.5 m, is stretched until it breaks. Assuming the wire obeys Hooke’s law throughout, calculate the extension of the specimen immediately before breaking.arrow_forwardA steel alloy specimen having a rectangular cross section of dimensions 18.6 mm × 3.4 mm (0.7323 in. × 0.1339 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 105000 N (23600 lbf) then(a) Determine the amount of elastic strain induced.(b) Determine the amount of plastic strain induced.(c) If its original length is 690 mm, what will be its final length after this force is applied and then released?The elastic modulus for steel is 207 GPa.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Pressure Vessels Introduction; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=Z1J97IpFc2k;License: Standard youtube license