Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 62P
The material properties of a machine part are Sut = 85 kpsi, f = 0.86, and a fully corrected endurance limit of Se = 45 kpsi. The part is to be cycled at σa = 35 kpsi and σm = 30 kpsi for 12 (103) cycles. Using the Gerber criterion, estimate the new endurance limit after cycling.
(a) Use Miner’s method.
(b) Use Manson’s method.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
1. A rotating l-in diameter solid round bar has a groove 0.1-in deep with a 0.1-radius machined
into it. The bar is made of AISI 1020 CD steel and is subjected to a purely reversing torque of
1800 lbf-in. For the S-N curve of the material, let f= 0.9.
1) Estimate the number of cycles to failure.
2) If the bar is also placed in an environment with a temperature of 750 °F, estimate the number
of cycles to failure.
Note: for pure shear stress state, find ta and Tm to replace oa and om. Apply the load factor k. =
0.59. To get safety factor against first-cycle yielding, use Sgy=0.577 Sy (based on DE theory).
For fatigue life or fatigue failure criteria, Replace Sut with Sgu. Ssu = 0.67Sµt
Determine the estimated endurance
strength in MPa to 1 decimal place for a
hot rolled steel 28 mm round bar for 95%
reliability. The ultimate strength is 650
MPa and the rod will be used as rotating
shaft at 70 C.
Your Answer:
3. The safe working stress of a belt is equal to the tight side tension over the product of the belt's
width and thickness. Find the width of the belt if a 610mm diameter pulley transmits 40 kW at 500 rpm, the
arc of contact is 144°, coefficient of friction is 0.35, safe working stress of the belt is 2.1 MPa and thickness
is 6mm.
Chapter 6 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 6 - A 10-mm steel drill rod was heat-treated and...Ch. 6 - Prob. 2PCh. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Repeat Prob. 6-5 with the specimen having an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Derive Eq. (6-17). Rearrange the equation to solve...Ch. 6 - For the interval 103 N 106 cycles, develop an...Ch. 6 - Estimate the endurance strength of a...
Ch. 6 - Two steels are being considered for manufacture of...Ch. 6 - A 1-in-diamctcr solid round bar has a groove...Ch. 6 - A solid square rod is cantilevered at one end. The...Ch. 6 - A rectangular bar is cut from an AISI 1020...Ch. 6 - A solid round bar with diameter of 2 in has a...Ch. 6 - The rotating shaft shown in the figure is machined...Ch. 6 - The shaft shown in the figure is machined from...Ch. 6 - Solve Prob. 6-17 except with forces F1 = 1200 lbf...Ch. 6 - Bearing reactions R1 and R2 are exerted on the...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with an alternating...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - The cold-drawn AISI KUO steel bar shown in the...Ch. 6 - Repeat Prob. 6-25 for a load that fluctuates from...Ch. 6 - An M14 2 hex-head bolt with a nut is used to...Ch. 6 - The figure shows a formed round-wire cantilever...Ch. 6 - The figure is a drawing of a 4- by 20-mm latching...Ch. 6 - The figure shows the free-body diagram of a...Ch. 6 - Solve Prob. 6-30 except let w1 = 2.5 in. w2 = l.5...Ch. 6 - For the part in Prob. 630, recommend a fillet...Ch. 6 - Prob. 33PCh. 6 - Prob. 34PCh. 6 - A part is loaded with a combination of bending,...Ch. 6 - Repeat the requirements of Prob. 6-35 with the...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 637 to 646 For the problem specified in the table,...Ch. 6 - For the problem specified in the table, build upon...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - Problem Number Original Problem, Page Number 637...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - Prob. 49PCh. 6 - Prob. 50PCh. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - Solve Prob. 6-17 except include a steady torque of...Ch. 6 - Solve Prob. 618 except include a steady torque of...Ch. 6 - In the figure shown, shaft A, made of AISI 1020...Ch. 6 - A schematic of a clutch-testing machine is shown....Ch. 6 - For the clutch of Prob. 657, the external load P...Ch. 6 - A flat leaf spring has fluctuating stress of max =...Ch. 6 - A rotating-beam specimen with an endurance limit...Ch. 6 - A machine part will be cycled at 350 MPa for 5...Ch. 6 - The material properties of a machine part are Sut...Ch. 6 - Repeat Prob. 662 using the Goodman criterion....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A component machined from a plate made of steel 45C8 (Sut = 630 N/mm2) is shown in figure below. It is subjected to a completely reversed axial force of 50 kN. The expected reliability is 90% and the factor of safety is 2. The size factor is 0.85.Determine the plate thickness t for infinite life, if the notch sensitivity factor is 0.8.arrow_forwardA material presents S-N fatigue behaviour shown on the right with the fatigue limit being 100 MPa. If a cylindrical bar made from the material has a diameter of 20 mm is subjected to repeated tensile stress along its axis, calculate the maximum allowable tensile load to ensure no occurrence of fatigue failure. Stress amplitude, S Fatigue limit 103 104 105 106 107 Cycles to failure, N (logarithmic scale) 108 10⁹ 1010arrow_forward4. A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. The values of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability.arrow_forward
- Part A For a hard aluminum notched part having notch dimension r = 0.75 in, geometric stress-concentration factor Kt = 2.8, material strength Sut = 50 kpsi, and bending loading type, find the Neuber factor, a (in inches). Part B Find the material's notch sensitivity, q. Part C Find the fatigue stress-concentration factor. Kf.arrow_forwardA shaft of diameter 25-0.04 mm is assembled in a hole of diameter 25+0.02 mm. -0.00 Match the allowance and limit parameter in Column I with its corresponding quantitative value in Column II for this shaft-hole assembly. Allowance and limit Quantitative parameter value (Column I) (Column II) Allowance 1 0.09 mm Q Maximum clearance 2 24.96 mm R Maximum material limit 3 0.04 mm for hole 4 25.0 mm Parrow_forward3. A motor is connected by a belt to pulley B. T, is the tight-side tensile force equal to 1800 N. The shaft spins at a constant speed, 650 rpm. The power delivered by the motor is 12.6 kW. On pulley A, connected to the load, the slack side of the belt has a tension equal to th of the tight side. b T T, B d shaft Dimensions are as follows: da 200 тm 300 тт | 250 тm |180 тm | 250 тm 26 тm dB dahaft a We analyzed a problem similar to this on Test 01 using static failure theories. Is this strictly correct? Because the shaft is spinning, would not a material particle see a time-varying reversal of the the bending stress as in the R.R. rotating beam test? Would a particle see a reversal of the torsional shear stress? Assume Sut = 370 MPa and Sy = 300 MPa. Ignore Marin factors. Ignore stress concentrations. Ignore direct shear stress (that due to V). Find the safety factors with respect to fatigue and yielding. Be guided by section 6-14 on combined loading.arrow_forward
- A simply supported shaft is shown. A constant magnitude distributed unit load p is applied as the shaft rotates subject to a time-varying torque that varies from Tmin to Tmax. For the data given, find the diameter of shaft required to obtain a safety factor of 2 in fatigue loading if the shaft is steel of Sut = 745 MPa and Sy = 427 Mpa. Assume no stress concentrations are present. Dimensions: L = 8 cm, a = 4 cm, b = 8 cm, p = 1000 N/cm, Tmin = 0 N-m, Tmax = 2000 N-m STEP-BY-STEP don't understand English very well, so please write in clear letters. please!arrow_forwardA bracket is under a loading condition shown below. It's made from a steel with yield strength (Sy) of 42 ksi and ultimate tensile strength (Sut) of 76 ksi. The diameter is 0.42 in and b = 1.75 in, with the load P fluctuate between 15 lbs (tension) and -5 lbs (compression). Using the modified Goodman or Gerber criterion, determine the fatigue factor of safety based on infinite life. If infinite life is not predicted, estimate the number of cycles to failure. Also check for yielding.arrow_forwardP Q R A shaft of diameter 250.04 mm is assembled in a hole of diameter 25-0.02 mm. Match the allowance and limit parameter in Column I with its corresponding quantitative value in Column II for this shaft-hole assembly. Allowance and limit Quantitative parameter value (Column I) (Column II) Allowance 1 0.09 mm Maximum clearance 2 24.96 mm Maximum material limit 3 0.04 mm for hole 4 25.0 mmarrow_forward
- A chain drive using bush roller chain transmits 5.6 kW of power. The driving shaft on an electric motor runs at 1440 r.p.m. and velocity ratio is 5. The centre distance of the drive is restricted to 550 ± 2% mm and allowable pressure on the pivot joint is not to exceed 10 N/mm2. The drive is required to operate continuously with periodic lubrication and driven machine is such that load can be regarded as fairly constant with jerk and impact. Design the chain drive by calculating leading dimensions, number of teeth on the sprocket and specify the breaking strength of the chain. Assume a factor of safety of 13.arrow_forwardA chain drive using bush roller chain transmits 5.6 kW of power. The driving shaft on an electric motor runs at 1440 r.p.m. and velocity ratio is 5. The centre distance of the drive is restricted to 550 ± 2% mm and allowable pressure on the pivot joint is not to exceed 10 N/mm2. The drive is required to operate continuously with periodic lubrication and driven machine is such that load can be regarded as fairly constant with jerk and impact. Design the chain drive by calculating leading dimensions, number of teeth on the sprocket and specify the breaking strength of the chain. Assume a factor ofarrow_forwardA hard-drawn steel wire extension spring has a wire diameter of 4mm, an outside coil diameter of 28 mm, and initial tension of 1200 N is applied to the spring. The spring shows an extension of 85 mm. The approximate number of turns is 25. From the given information: Determine the physical parameters of the spring such as mean diameter, spring index, maximum shear stress, total number of turns, Wahl’s stress factor, free length of the spring, and pitch of the coilarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Stresses Due to Fluctuating Loads Introduction - Design Against Fluctuating Loads - Machine Design 1; Author: Ekeeda;https://www.youtube.com/watch?v=3FBmQXfP_eE;License: Standard Youtube License